A Vance company - serving Whitney, NV
Gate Repair in Whitney, NV | Vance Gate Repair Whitney

Gate Repair in Whitney - Fixed Today, No Surprise Invoice

Most gate faults are diagnosed and fixed on the first visit. You get the price before we start, and the gate is left working and safe before we leave.

We answer around the clock

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Trusted Gate Repair for Whitney Homeowners

A gate that won’t open stops being a convenience and becomes a security problem. Electric gates that drift, automatic gates that reverse halfway, hinges that drag on desert-blown sand, and locks that bind after a summer of 100-degree heat are the calls we take most in Whitney. Our technicians have up to 12 years of experience with residential swing and slide gates, and we service nine major automation brands so we can work on whatever motor is already on your property. Same-day repair is often available across Whitney, and a live person answers the phone at any hour. Call (844) 797-4861.

Call (844) 797-4861

What Our Gate Repair Service Includes

Electric Gate Repair

Electric gates fail in a few recognizable ways: the operator runs but the gate doesn’t move, the gate moves but stalls under load, or the control board throws a fault you can’t read. Whitney’s wind-driven grit works its way into tracks and pivot points, and voltage sags during monsoon season will trip a control board that was fine a week earlier. We meter the incoming power, test the board, and inspect the drive hardware before we quote anything.

Electric Gate Repair

Automatic Gate Repair

Automatic gates depend on limit switches, photo-eyes, and a logic board all agreeing with each other. When one drifts, the gate behaves erratically – reversing, stopping short, or refusing to close. A limit switch set even a few degrees past travel will trigger symptoms many homeowners mistake for a dead motor. We read the switch positions, reset them, and photograph the new settings so the next technician has a starting point.

Automatic Gate Repair

Hinge & Post Repair

Swing gates hang their weight on hinges, and a post that has shifted a quarter inch at the base shows up as a gate that sags an inch at the far edge. Whitney’s caliche-heavy soil holds posts well in most spots but moves seasonally in others. We check post plumb with a level, inspect hinge plates for elongation, and repair or re-set the hardware that is actually causing the drag.

Hinge & Post Repair

Gate Realignment

Realignment is the fix for a gate that scrapes, rubs, or catches on the latch side without an obvious broken part. Over years, heat expansion, soil movement, and normal wear pull a gate out of square with its post. We measure the gap along the full swing or slide path, correct the frame and hardware, and record the before-and-after clearances in your photo file.

Lock Repair

Gate locks – mechanical, magnetic, or integrated into an access-control keypad – fail differently than a house door lock. Dust fouls the mechanism, and a strike plate that has moved a sixteenth of an inch makes a lock feel broken when it just needs alignment. We repair the lock, adjust the strike, and confirm the release works from both sides before we leave.

Weld & Rust Repair

Metal gates in the Las Vegas valley deal with dry heat and occasional monsoon moisture, which is a different corrosion pattern than coastal rust. Failure usually starts at a weld seam or a factory-drilled hole, not across a flat panel. We cut out the compromised section, weld in new material matched to the gate’s gauge, and treat the repair so it doesn’t come back next season.

Need help today?Fast, friendly service and a no-obligation free estimate.

Call (844) 797-4861

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Brands We Service for Gate Repair

professional gate repair service
Brands We Service for Gate Repair

We work on the automation that’s already on your gate rather than steering you toward a replacement. Ghost Controls operators are common on rural-edge properties and DIY-installed swing gates, and we know how their control boards behave when a battery or solar supply drops below threshold. DoorKing equipment shows up on gated entries and light commercial driveways, and its loop-detector and keypad logic is where most of the troubleshooting lands. Elite slide operators are built heavy, which means when they fail the problem is usually in the drive chain or the limit cams, not the motor itself.

Mighty Mule is the brand we see most often on gates installed by previous homeowners, and its control boards are sensitive to voltage and moisture in ways we’ve learned to test for directly. Whether your gate runs Mighty Mule, Ghost Controls, DoorKing, Elite, or another make entirely, we can help. We bring the meters and the documentation habit to every brand.

BeforeBefore
AfterAfter

Signs You Need Gate Repair Right Now

  • The gate reverses before it closes. A gate that opens, pauses, and reverses is usually reading a false obstruction from a misaligned photo-eye (the infrared beam that stops the gate if something crosses the path). Running it anyway wears the motor and can leave your driveway open overnight.
  • The gate drags or scrapes the ground. Metal-on-concrete contact means a hinge, post, or frame has moved. Left alone, the drag loads the operator and shortens the life of the motor.
  • The motor runs but the gate doesn’t move. This points to a stripped gear, a broken arm, or a chain that’s jumped its sprocket. Continuing to cycle it turns a small repair into a drive-train replacement.
  • A keypad or remote stops responding. Access control failures are often a single failed receiver, a dead battery in the remote, or a wiring connection that loosened after a hot season. We test each link in the chain before quoting a part.
  • Visible rust or cracks at a weld. A weld seam that’s started to crack is a structural issue, not cosmetic. It needs attention before the gate sags under its own weight.

Our Gate Repair Process – Step by Step

Technician performing metal gate repair with an angle grinder
Our Gate Repair Process – Step by Step
  1. 1
    Call and describe the symptom. A live person takes the call 24/7. We ask what the gate is doing, what brand the operator is, and how old the installation looks, so the technician arrives with the right test equipment.
  2. 2
    Written estimate before any work. Under The Haven Standard, the flat price is written and handed to you before a tool comes out of the case. That’s Clause 1: have it in writing. No verbal ballpark, no surprise invoice at the end.
  3. 3
    Diagnosis with real tools. We meter the power supply, read the limit-switch positions, test the photo-eyes with a reflector check, and inspect the hinges and post plumb. The findings get written down, not just told to you.
  4. 4
    Repair and document. We complete the repair, then photograph what we found, what we adjusted, and what we installed. You get a photo log of every adjustment and a written record of the part number installed, filed in the job record.
  5. 5
    Confirm and walk you through it. We cycle the gate through a full open-and-close sequence, test the release from both sides, and show you the documentation before we leave. The 365-Day Done Right Promise backs the repair: if it isn’t right, we make it right within that window at no additional charge.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Get the price in writing before anything starts.Serving Whitney - a real person answers, day or night.
Call now

How Much Does Gate Repair Cost in Whitney?

Most gate repair calls in Whitney fall between $150 and $650 depending on what failed. Here’s a realistic breakdown by the work involved:

Repair Type Typical Whitney Range
Lock or strike-plate repair $95 – $200
Hinge replacement or minor realignment $150 – $320
Limit-switch or photo-eye reset $150 – $280
Control board replacement $280 – $550
Weld and rust repair (per section) $200 – $500
Post re-set or structural realignment $350 – $800
Drive-train or gear repair $300 – $650

What moves the price: the brand and age of the operator, whether the control board has failed or just needs a reset, and whether the post has shifted enough to require structural work. We meter the supply and read the switches before we quote, so the range you get is based on your gate, not a phone guess. The written price is agreed before any work starts. We also offer a free second opinion on any written estimate from another company – bring the paperwork and we’ll review it at no cost. For a broader look at this service, see our Gate Repair in Whitney page.

Gate Repair Near Whitney – Our Service Area

Professional technician applying sealant for stone pillar gate repair
Gate Repair Near Whitney – Our Service Area

We handle gate repair across Whitney and the surrounding east valley, including Sunrise Manor, Winchester, and Paradise, plus larger jobs into Henderson, Enterprise, and Spring Valley. Response times run same-day for most Whitney calls when you reach us in the morning. Homeowners nearby in North Las Vegas and Summerlin are covered too. If your gate is in a neighboring area, call and we’ll confirm the earliest availability. For residents just east, our Gate Repair in Sunrise Manor page covers what we see most there.

Serving Whitney, NV – Our Local Coverage Area

We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions – Gate Repair in Whitney

Two professional workers installing a modern horizontal slat metal entry gate
Frequently Asked Questions – Gate Repair in Whitney

Schedule Your Gate Repair Service in Whitney Today

If your Whitney gate is dragging, reversing, or staying locked when it shouldn’t, call (844) 797-4861. A live person answers any hour, you’ll get a flat written price before any work starts, and you’ll leave with a documented photo record of what was found and fixed. The 365-Day Done Right Promise backs the repair. Estimates are free and there’s no obligation.

Written by the team at Vance Gate Repair.

Why Whitney Chooses Vance Gate Repair Whitney

We set the standard for gate repair in Whitney.

30-60 Min Response

Fast dispatch across Whitney. Same-day and after-hours emergency service available.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Whitney

Getting your gate repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your gate repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Whitney - typically within 30-60 minutes.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and 100% satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local gate repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A background-checked tech heads outLicensed & insured, typically within the hour.
  4. 4
    You approve before work beginsNothing starts until you say go.

What Whitney Customers Say

Trusted by homeowners across Whitney and surrounding areas.

★★★★★

"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."

Nadine C.
★★★★★

"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."

Douglas N.
★★★★★

"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."

Camille R.

Ready for Gate Repair in Whitney?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast after-hours help in Whitney.

(844) 797-4861

Request a Free Estimate in Whitney

Tell us about your gate repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - 24/7 Dispatch