A Vance company - serving Whitney, NV
Gate Parts & Welding in Whitney, NV | Vance Gate Repair Whitney

Gate Parts & Welding in Whitney - Welded and Fitted, Priced Up Front

Hinges, wheels, tracks and steelwork made to fit your gate rather than forced from a generic kit. Measured, fabricated and fitted, with the price agreed before we cut anything.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Trusted Gate Parts & Welding for Whitney Homeowners

A gate that drags, sags, or won’t latch is usually a hardware problem, not a motor problem. In Whitney, most of what we find on a failing driveway gate is worn hinges, a post that has shifted, a bent rail, or a latch that stopped lining up months before the motor gave out. We replace and weld those parts and get the gate swinging clean again.

Call (844) 797-4861

Our technicians have up to 12 years of experience on residential and light commercial gates, and we work on whatever hardware is already on your property rather than steering you toward a full replacement. Same-day service is often available in Whitney, and a live person answers the phone at (844) 797-4861 around the clock. Under the Haven Standard, you get a written price before any work starts and a photo record when we leave.

What Our Gate Parts & Welding Service Includes

Every job below starts with a written scope and a flat price. We hand it to you before anyone picks up a tool, so you know exactly what’s being replaced, what’s being repaired, and what it costs.

Hinge Replacement

Hinges carry the entire weight of a swing gate, and when they wear, the gate drops and drags on the ground. You’ll notice it first as a scrape at the bottom edge, then as a gate that won’t close flush. We remove the worn hinges, check the post and frame for damage the sag may have caused, and install new hardware sized to the gate’s weight, then photograph the alignment before we leave.

Hinge Replacement

Post Replacement

A gate post that has rotted, heaved, or been struck by a vehicle throws every other part out of line. When we replace a post, we set it plumb and at the correct depth for the gate’s span, then re-hang the gate and re-check every hinge and latch point. Post work is the foundation of the whole assembly, so we document the set with photos and note it in the job record for the next technician.

Post Replacement

Rail Repair

Rails are the horizontal bars that hold the gate’s shape, and a bent or cracked rail lets the frame flex. Left alone, that flex puts strain on hinges and the operator arm until something fails. We straighten or replace damaged rails and weld frame joints back to solid, matching the original profile so the gate looks the same when we’re done.

Rail Repair

Custom Welding

Some gates need a repair that doesn’t come in a box: a cracked frame corner, a broken picket, a reinforcement plate where the operator arm bolts on. We do that fabrication on site with a portable welder, matching the existing metal and finishing the weld so it holds under daily use. Every weld is inspected and photographed, and we note the material and method in your record.

Gate Rollers

Sliding gates ride on rollers, and worn rollers make the gate grind, jump the track, or stop short. We replace the rollers, check the track for bends and debris, and reset the gate so it travels smoothly end to end. If the roller brackets are bent or the track is lifting, we fix that too rather than just swapping the wheel and calling it done.

Latch & Lock

A latch that doesn’t catch is a security gap, and it often shows up as a gate that rattles in the wind or a lock that takes two hands to work. We replace worn latches and locks, align the strike so the gate closes firmly, and test it by hand before we leave. For gates tied to an access-control keypad or entry system, we check that the latch releases cleanly when the system calls for it.

Need help today?Fast, friendly service and a no-obligation free estimate.

Call (844) 797-4861

Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Brands We Service for Gate Parts & Welding

professional gate repair service
Brands We Service for Gate Parts & Welding

We service nine major gate-automation brands, which means we can work on whatever motor is already on your property instead of pushing a replacement. That matters most on older gates, where the hardware and the operator were matched years ago and the simplest fix is to repair the parts you already have. On Ghost Controls systems, for example, we know where the arm bracket tends to loosen over time and how to re-weld or re-bolt it so the operator stays aligned. On DoorKing equipment, we’ve worked enough units to know how the latch and strike interact with the access-control side, which saves time when a gate won’t release on command.

We also service Elite and Mighty Mule operators, along with LiftMaster, FAAC, BFT, Linear, and Viking. Each brand wears differently, and knowing the common failure points helps us diagnose faster and quote accurately. Whether you have a Ghost Controls arm, a DoorKing entry system, or any other make on the gate, we can help.

BeforeBefore
AfterAfter

Signs You Need Gate Parts & Welding Right Now

  • The gate drags or scrapes the ground. That’s usually a worn hinge or a post that has shifted, and it puts extra load on the operator every time the gate moves. Left alone, it can burn out the motor.
  • The gate sags and won’t latch. A sagging gate throws the latch out of line and leaves a gap someone could push through. It’s a hardware alignment problem we can usually fix the same day.
  • You see rust, cracks, or a broken weld at the frame. Cracks spread under daily use, and a broken weld at the operator bracket can let the arm tear free. This is the kind of repair that’s cheaper to weld now than to replace later.
  • The gate jumps the track or grinds when it slides. Worn rollers or a bent track cause the grinding, and both get worse with every cycle. Replacing the rollers early protects the track and the motor.
  • The latch or lock won’t catch securely. A latch that doesn’t seat is a security gap, and it often means the strike has moved or the hinge has worn. We realign it so the gate closes firmly and locks the way it should.

Our Gate Parts & Welding Process – Step by Step

Technician performing metal gate repair with an angle grinder
Our Gate Parts & Welding Process – Step by Step
  1. 1
    We take your call and dispatch a technician. A live person answers at any hour, and we confirm your gate’s setup and the problem before we arrive. You get the technician’s name and photo before they show up.
  2. 2
    We inspect the system and photograph what we find. The technician checks hinges, posts, rails, rollers, and the latch, plus the operator if the gate is automated. Every finding gets a photo, and we test the gate through a full cycle to see where it binds.
  3. 3
    We write the scope and the price. You get a flat written price before any work begins, listing what will be replaced or welded and what the parts cost. No surprise invoice at the end, per Haven Standard Clause 1.
  4. 4
    We do the repair. Hinges, rollers, posts, rails, latches, and welds are handled on site using the correct hardware for your gate’s weight and frame. We re-check alignment and test the gate by hand and with the operator.
  5. 5
    We document and hand over the record. Before we leave, you get a photo log of every adjustment and a written record of the part numbers installed, plus the 365-Day Done Right Promise covering the work.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Get the price in writing before anything starts.Serving Whitney - a real person answers, day or night.
Call now

How Much Does Gate Parts & Welding Cost in Whitney?

Most swing-gate hinge replacements in Whitney run $180 to $320 per hinge set, depending on the hinge type and whether the post needs work. Roller replacement on a sliding gate typically lands between $140 and $280, and a latch or lock replacement runs $120 to $250. Rail repair and smaller custom welds usually fall between $200 and $450, and full post replacement runs $450 to $900 or more, since setting a post plumb and re-hanging the gate is the most involved job in this category.

What moves the price: the gate’s weight and span, whether the metal is steel, aluminum, or wrought iron, and how much damage the failing part caused before you called. Repairs caught early cost less, because worn hinges and rollers that are replaced quickly don’t bend rails or strain the operator. To avoid overpaying, ask for the written scope before work starts so you can see exactly what’s being replaced. Our free estimate includes the inspection, the diagnosis, and a written price agreed before anyone starts, and we’ll review a written estimate from another company at no cost as a second opinion.

Gate Parts & Welding Near Whitney – Our Service Area

Professional technician applying sealant for stone pillar gate repair
Gate Parts & Welding Near Whitney – Our Service Area

We serve Whitney and the surrounding Las Vegas Valley, including Sunrise Manor, Paradise, Winchester, Henderson, Enterprise, Spring Valley, North Las Vegas, and Boulder City. Typical response is same-day for repair calls in the Whitney core and next-day for outlying areas like Sandy Valley. For these neighboring communities, see our Gate Parts & Welding in Sunrise Manor page, and for nearby coverage on the east side, see Gate Parts & Welding in Paradise.

Serving Whitney, NV – Our Local Coverage Area

We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions – Gate Parts & Welding in Whitney

Two professional workers installing a modern horizontal slat metal entry gate
Frequently Asked Questions – Gate Parts & Welding in Whitney

Schedule Your Gate Parts & Welding Service in Whitney Today

Worn hinges, a sagging post, or a cracked weld only gets worse, and the repair gets bigger with it. Call (844) 797-4861 and a live person will take your details and dispatch a technician, often the same day in Whitney. You get a free estimate, a written price agreed before work starts, a documented photo record, and the 365-Day Done Right Promise. No obligation, no surprise invoice.

Written by the team at Vance Gate Repair.

Why Whitney Chooses Vance Gate Repair Whitney

We set the standard for gate parts & welding in Whitney.

30-60 Min Response

Fast dispatch across Whitney. Same-day and after-hours emergency service available.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Whitney

Getting your gate parts & welding handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your gate parts & welding needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

Licensed Technician Dispatched

A background-checked, certified technician arrives in Whitney - typically within 30-60 minutes.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and 100% satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local gate parts & welding pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A background-checked tech heads outLicensed & insured, typically within the hour.
  4. 4
    You approve before work beginsNothing starts until you say go.

What Whitney Customers Say

Trusted by homeowners across Whitney and surrounding areas.

★★★★★

"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."

Nadine C.
★★★★★

"Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."

Douglas N.
★★★★★

"Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."

Camille R.

Ready for Gate Parts & Welding in Whitney?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast after-hours help in Whitney.

(844) 797-4861

Request a Free Estimate in Whitney

Tell us about your gate parts & welding needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Local Service Coverage
Call Now - 24/7 Dispatch