Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterElectric Gate Repair in Whitney, NV
Most electric gate failures in Whitney come down to one of four things: a misaligned photo-eye, a limit switch that has drifted out of position, a control board that took a surge, or an actuator arm that has worn past its adjustment range. We diagnose which one it is, write the price down, and hand it to you before we touch a tool. Call Vance Gate Repair Whitney at (844) 797-4861 and a live person answers, day or night.
This page covers the electrical and automation side of our work: motors, openers, control boards, safety sensors, keypads, and access hardware. If the gate itself is dragging, bent, or off its hinges, that’s structural work and belongs with our Gate Repair in Whitney service instead.
LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule units all come through our queue in Whitney. That matters because we don’t talk you into a new operator when the one you own is serviceable. Our technicians have up to 12 years of experience, and every job is governed by The Haven Standard: written price before work starts, a documented photo record on every visit, and the 365-Day Done Right Promise behind the repair. You can see the full scope of what we handle on our home page.
When You Need Electric Gate Repair
Whitney sits in the shadow of the McCullough Range, and the swings between summer heat and cool spring evenings are hard on outdoor electronics. Gate operators live outside all year. Here’s what we get called about most.
- The gate stops mid-travel. Often a limit switch has drifted, or a photo-eye (the infrared beam that stops the gate if something crosses the path) has been knocked out of alignment by a trash can or a kid on a bike. Alignment is a small job with a written price.
- The gate reverses for no reason. A safety sensor is usually reading an obstruction that isn’t there. Dust, spider webs, and low sun angle at the wrong hour all do this. We test the beam path and photograph the fix.
- The remote works sometimes. Intermittent range problems point at antenna placement, a dying battery, or a receiver that’s picking up interference. We check all three rather than selling you a new remote you don’t need.
- Nothing happens when you press the button. Could be the control board, the transformer, or a tripped breaker feeding the operator. We trace power before we quote a board, because a $4 fuse and a $340 board look identical from the driveway.
- The arm grinds or the gate lurches. On swing gates, the actuator arm or its bracket is usually worn. On sliding gates, it’s often a chain or a roller issue the motor is fighting.
- The keypad or entry panel stopped accepting codes. We see this on DoorKing and Elite access units. Wiring at the post takes sun and moisture. Under Clause 4 of The Haven Standard, every visit includes a documented photo record at no additional charge, so you can see what we found.
Our Electric Gate Repair Process

The order matters. Diagnosing before quoting is what keeps the price on the page honest instead of letting it drift once we’re already there.
- Take the call in person. Someone live answers at any hour. We ask what the gate is doing, which brand the operator is, and how the gate has behaved for the past month.
- Test, then photograph. At the property we check the photo-eyes, the limit switches, the control board, the wiring terminations, and the operator’s power supply. We photograph readings and settings before we change anything.
- Write the price. You get a written scope and a flat written price before any work begins. Haven Standard Clause 1 (“Have it in writing”) exists so there’s no surprise invoice at the end.
- Do the repair. Board swap, sensor realignment, limit reset, actuator replacement, wiring repair, or keypad reprogramming, depending on what we found.
- Cycle-test and document. We run the gate through open, close, and obstruction-reverse multiple times, then photograph every adjustment and write down the part number installed.
- Leave the record with you. The photo log and written record go to you and into the job file, so the next technician, ours or anyone else’s, starts from facts.
Before
AfterElectric Gate Repair Pricing in Whitney
Here’s the range you should expect in the Whitney market. These are typical figures, not a quote for your specific gate, and the written price you receive is the price you pay.
| Repair | Typical range | What drives it |
|---|---|---|
| Photo-eye / safety sensor realignment | $95 – $180 | Sensor condition, wiring at the post |
| Limit switch adjustment or reset | $110 – $195 | Access to the operator housing |
| Remote / receiver / keypad programming | $85 – $220 | Brand, number of remotes, panel type |
| Control board replacement | $280 – $640 | Brand, board availability, surge damage |
| Swing-gate actuator arm replacement | $420 – $950 | Brand, arm length, bracket condition |
| Sliding-gate operator or motor service | $350 – $1,100 | Motor size, chain, roller condition |
| Wiring repair at the post or control box | $140 – $380 | Run length, conduit condition |
Brand and board availability move the numbers more than anything else. A Mighty Mule board is often cheaper and easier to source than a DoorKing board, and a Ghost Controls operator that’s already on the gate needs the same diagnosis either way. What we don’t do is quote after the fact. The number gets written down first.
If you’ve gotten a written estimate from another company, bring the paperwork. We’ll review it at no cost as a second opinion. It’s a straightforward way to confirm you’re being quoted for the actual problem.
How much does electric gate repair cost in Whitney?

Most electric gate repairs in Whitney land between $95 and $380 for sensor, adjustment, and wiring work, with board and motor replacements running $280 to $1,100 depending on brand and parts. The written price you receive before work starts is the final price. Call (844) 797-4861 for an exact quote on your gate.
Can you repair my brand of gate operator?
Yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. Because we work on whatever motor is already on the property, you won’t get steered toward a replacement when a repair solves it. If the board is truly dead and out of production, we’ll tell you that plainly with the reasoning, and price both paths in writing.
Is it cheaper to repair my electric gate or replace the operator?

Repair is cheaper in most cases. A sensor realignment, a limit reset, or a wiring fix frequently runs under $200 and restores full function. Replacement starts making sense when the board is unobtainable, the housing has rusted through, or the motor has failed after years of service. We quote the repair first. Replacement only gets priced when the repair can’t be done. Call (844) 797-4861 and we’ll talk through what you’re hearing at the gate.
Should I try to fix an electric gate myself?
No. Gate operators run on line voltage, and a swing-gate actuator arm holds serious spring tension. Both can cause injury. The safe homeowner move is to check the obvious outside items: clear debris from the photo-eye path, confirm the breaker hasn’t tripped, and test a fresh remote battery. If those don’t solve it, that’s when a trained technician should take over. Our technicians are background-checked and dispatched with their name and photo provided before arrival. Call (844) 797-4861 and we’ll get a live person on the line.
How do I know the repair was done right?

You’ll have it in writing. Every visit includes a documented photo record of what was found, what was adjusted, and what was replaced, filed in the job record and left with you. Repairs are covered by the 365-Day Done Right Promise: if something isn’t right, we make it right at no additional charge within that window. That’s the same documentation habit the company started with on commercial access-control work, carried to every driveway gate we touch.
Talk to Us About Your Gate
If the operator is misbehaving, the sensors are giving you trouble, or you just want a second set of eyes on a written estimate you already have, call (844) 797-4861 for a free estimate. A live person answers at any hour. You’ll get a written price before any work begins, a documented record when we leave, and a repair backed by our 365-Day Done Right Promise. That’s how we handle every electric gate in Whitney.
Written by the team at Vance Gate Repair Whitney, serving Whitney.