Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Parts & Welding Across Whitney
Whitney runs on tract gates. Almost every driveway swing gate and community pedestrian gate in this part of the Las Vegas Valley went in during the original builder phase, and the parts on them are now 15 to 25 years old. We know the subdivisions off Whitney Ranch Drive and Russell Road well enough to guess what we’ll find before we open the operator housing: a builder-grade motor wired to a shared circuit, rattle-can hinges, and a post that has shifted a half-inch in the caliche. Call (844) 797-4861 and a live person picks up, day or night.
Why Vance Gate Repair Whitney Is Whitney’s Preferred Gate Parts & Welding Company
Homeowners in Whitney tend to research first. They’ve read the three-star reviews, they’ve gotten a verbal estimate from someone who never wrote anything down, and they want the price visible before they commit. That’s the whole reason we hand over a written scope and a written price before a tool comes out of the truck – no “call for a quote,” no invoice that grew on the way to the mailbox. Our Gate Parts & Welding team works on whatever motor is already bolted to your gate, whether that’s a tired LiftMaster, a Linear, or a Ghost Controls arm someone added later.
Every visit leaves a photographed record: what we found, what we set, what we installed. Under the Haven Standard, that record is included at no charge, and the 365-Day Done Right Promise covers the work for a full year. If a weld fails or a hinge we replaced starts binding again, we make it right.
Whitney is also a newer suburb, and that shapes the jobs. These aren’t historic ironwork gates on century-old posts. They’re steel and aluminum gates bolted to block walls in HOA-governed subdivisions, which means the fix and the finish both have to survive committee review. Speaking the same language as your association matters as much as getting the swing true. If you’re comparing us to another written estimate, bring it by – the second opinion is free.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Parts & Welding Services in Whitney

Hinge Replacement in Whitney
Most dragging gates in Whitney start at the hinge, not the motor. Builder hinges wear flat, the gate drops a quarter-inch, and suddenly the operator is lifting weight it was never sized for. We cut out the worn hinge, weld on a replacement rated for the gate’s actual weight, and photograph the new alignment so you can see the gap closed.

Post Replacement in Whitney
This is the Whitney specialty. Caliche-heavy desert soil and shallow builder footings mean hinge posts settle and lean, which throws the whole gate out of plumb. A post replacement means digging a new footing to true depth, setting the post, and verifying the latch and operator afterward. Skip the post and the sag comes back within a season.

Rail Repair in Whitney
Monsoon gusts rack lighter aluminum pedestrian gates, cracking welds at the rail and bending the frame out of square. We straighten the rail, reweld the joint, and check that the keypad and loop detector still trigger reliably once the geometry is corrected. Cosmetic touch-up follows the perimeter wall’s existing color.

Custom Welding in Whitney
Some Whitney gates need a piece that was never made – a repair plate, a motor bracket for an odd retrofit, a replacement latch tab. Our custom welding work is done on-site where possible, and every weld gets a documented photo and a written part description so the next technician isn’t guessing.
Before
AfterTrusted Brands We Service in Whitney
We work on nine major gate-automation brands, including Linear, Viking, Ghost Controls, and DoorKing, along with LiftMaster, FAAC, BFT, Elite, and Mighty Mule. That range matters in Whitney because a single subdivision can have three different operators bolted to nearly identical gates depending on which builder phase went in when. We don’t stock parts, so we’re not steering you toward a replacement to move inventory. We service what’s on your property, order what’s needed, and schedule the return visit with a written price in hand.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Parts & Welding Problems We See in Whitney Homes

- Builder-grade operators on a shared 15-amp circuit. Many Whitney tract homes have a LiftMaster or Linear wired to the same circuit as exterior outlets with no dedicated disconnect. During summer AC load the voltage drops and the operator faults intermittently, which reads like a dead motor when the motor is fine.
- Posts settled in caliche soil. The same expansive desert ground that makes Whitney lots cheap to grade makes footings shallow and unstable. After a monsoon soak, a post can shift enough to misalign the latch and stop the keypad entry from registering.
- Racked aluminum pedestrian gates. High-wind events twist lighter gates and crack rail welds. A straightened rail with a fresh weld usually holds, but only if the post underneath is sound.
- HOA finish mismatch. A welded repair that isn’t powder-coat matched to the approved perimeter color can fail an association inspection even when the gate works perfectly. We check the wall finish before we touch the gate.
Pricing for Gate Parts & Welding in Whitney, NV
Whitney pricing runs in predictable ranges because the housing stock is uniform. A hinge replacement typically runs $150 – $320 depending on how many hinges and whether the gate has to come off the post. A post replacement, footing included, usually lands between $450 – $900 depending on depth required and access. Rail repair and weld work runs $125 – $400. Custom welding and bracket fabrication is $200 – $600 depending on the piece. Latches and locks add $95 – $250. What moves the number is access to the hinge post, whether the footing has to be dug deeper than the builder went, and whether finish matching is required. The flat price is written and agreed before work starts, and if the quote changes we explain why before we continue. Estimates are free.
We Also Serve Cities Near Whitney

We work the surrounding valley too – Sunrise Manor, Winchester, Paradise, and Las Vegas all fall within the same service footprint, and the same Haven Standard applies to every call. If you’re outside Whitney proper, we still serve Whitney and these neighboring areas. The written price and documented photo record travel with the job regardless of the address.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Parts & Welding in Whitney

Usually, yes. Most Whitney builder-era operators were wired to a shared 15-amp circuit with no dedicated disconnect, and during peak summer load the voltage sags and the operator faults or trips. A dedicated circuit with its own disconnect resolves the intermittent failures in the large majority of cases. Call (844) 797-4861 for an exact quote – estimates are free.
Yes, and it’s one of the trickier jobs in Whitney because the original gates were often installed manually and never had power or conduit run to them. Adding a LiftMaster, Linear, or Ghost Controls operator usually means trenching a power line, pulling a permit, and setting a footing for the operator arm. That work is measured, ordered, and scheduled – it’s not a same-day dispatch. We provide a written scope and a written price before anything is ordered. Call (844) 797-4861 to schedule a free measure.
Because the hinge post has settled, not the hinges. In Whitney’s caliche-heavy soil, a shallow builder footing can shift after monsoon saturation and throw the gate out of plumb. Tightening hinges on a leaning post just masks the problem for a few weeks. A post replacement to true depth is the real fix. Call (844) 797-4861 for a free estimate.
No, and this is the most common Whitney compliance failure we see. An HOA-governed subdivision can reject a welded repair or replacement hinge that isn’t finish-matched to the approved perimeter color, even if the gate swings perfectly. We check the wall’s existing finish and match it before we weld, so the repair passes on the first inspection. Call (844) 797-4861 for an exact quote – estimates are free.
Yes. Photo-eyes are the infrared beam that stops the gate if something crosses its path, and a Whitney tract gate without them is a genuine safety hazard, especially on a shared driveway where kids and pets move through. Adding a matched set of photo-eyes is usually a straightforward retrofit on most modern operators. Call (844) 797-4861 to schedule the work.
If your Whitney gate is dragging, sagging, or tripping the breaker, call (844) 797-4861 for a free estimate. A live person answers any hour, a written price comes before any work starts, and you get a documented photo record when we leave.
Written by the team at Vance Gate Repair.