Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Parts & Welding for Whitney Homeowners
A gate that drags, sags, or won’t latch is usually a hardware problem, not a motor problem. In Whitney, most of what we find on a failing driveway gate is worn hinges, a post that has shifted, a bent rail, or a latch that stopped lining up months before the motor gave out. We replace and weld those parts and get the gate swinging clean again.
Our technicians have up to 12 years of experience on residential and light commercial gates, and we work on whatever hardware is already on your property rather than steering you toward a full replacement. Same-day service is often available in Whitney, and a live person answers the phone at (844) 797-4861 around the clock. Under the Haven Standard, you get a written price before any work starts and a photo record when we leave.
What Our Gate Parts & Welding Service Includes
Every job below starts with a written scope and a flat price. We hand it to you before anyone picks up a tool, so you know exactly what’s being replaced, what’s being repaired, and what it costs.
Hinge Replacement
Hinges carry the entire weight of a swing gate, and when they wear, the gate drops and drags on the ground. You’ll notice it first as a scrape at the bottom edge, then as a gate that won’t close flush. We remove the worn hinges, check the post and frame for damage the sag may have caused, and install new hardware sized to the gate’s weight, then photograph the alignment before we leave.

Post Replacement
A gate post that has rotted, heaved, or been struck by a vehicle throws every other part out of line. When we replace a post, we set it plumb and at the correct depth for the gate’s span, then re-hang the gate and re-check every hinge and latch point. Post work is the foundation of the whole assembly, so we document the set with photos and note it in the job record for the next technician.

Rail Repair
Rails are the horizontal bars that hold the gate’s shape, and a bent or cracked rail lets the frame flex. Left alone, that flex puts strain on hinges and the operator arm until something fails. We straighten or replace damaged rails and weld frame joints back to solid, matching the original profile so the gate looks the same when we’re done.

Custom Welding
Some gates need a repair that doesn’t come in a box: a cracked frame corner, a broken picket, a reinforcement plate where the operator arm bolts on. We do that fabrication on site with a portable welder, matching the existing metal and finishing the weld so it holds under daily use. Every weld is inspected and photographed, and we note the material and method in your record.
Gate Rollers
Sliding gates ride on rollers, and worn rollers make the gate grind, jump the track, or stop short. We replace the rollers, check the track for bends and debris, and reset the gate so it travels smoothly end to end. If the roller brackets are bent or the track is lifting, we fix that too rather than just swapping the wheel and calling it done.
Latch & Lock
A latch that doesn’t catch is a security gap, and it often shows up as a gate that rattles in the wind or a lock that takes two hands to work. We replace worn latches and locks, align the strike so the gate closes firmly, and test it by hand before we leave. For gates tied to an access-control keypad or entry system, we check that the latch releases cleanly when the system calls for it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Brands We Service for Gate Parts & Welding

We service nine major gate-automation brands, which means we can work on whatever motor is already on your property instead of pushing a replacement. That matters most on older gates, where the hardware and the operator were matched years ago and the simplest fix is to repair the parts you already have. On Ghost Controls systems, for example, we know where the arm bracket tends to loosen over time and how to re-weld or re-bolt it so the operator stays aligned. On DoorKing equipment, we’ve worked enough units to know how the latch and strike interact with the access-control side, which saves time when a gate won’t release on command.
We also service Elite and Mighty Mule operators, along with LiftMaster, FAAC, BFT, Linear, and Viking. Each brand wears differently, and knowing the common failure points helps us diagnose faster and quote accurately. Whether you have a Ghost Controls arm, a DoorKing entry system, or any other make on the gate, we can help.
Before
AfterSigns You Need Gate Parts & Welding Right Now
- The gate drags or scrapes the ground. That’s usually a worn hinge or a post that has shifted, and it puts extra load on the operator every time the gate moves. Left alone, it can burn out the motor.
- The gate sags and won’t latch. A sagging gate throws the latch out of line and leaves a gap someone could push through. It’s a hardware alignment problem we can usually fix the same day.
- You see rust, cracks, or a broken weld at the frame. Cracks spread under daily use, and a broken weld at the operator bracket can let the arm tear free. This is the kind of repair that’s cheaper to weld now than to replace later.
- The gate jumps the track or grinds when it slides. Worn rollers or a bent track cause the grinding, and both get worse with every cycle. Replacing the rollers early protects the track and the motor.
- The latch or lock won’t catch securely. A latch that doesn’t seat is a security gap, and it often means the strike has moved or the hinge has worn. We realign it so the gate closes firmly and locks the way it should.
Our Gate Parts & Welding Process – Step by Step

- 1
We take your call and dispatch a technician. A live person answers at any hour, and we confirm your gate’s setup and the problem before we arrive. You get the technician’s name and photo before they show up.
- 2
We inspect the system and photograph what we find. The technician checks hinges, posts, rails, rollers, and the latch, plus the operator if the gate is automated. Every finding gets a photo, and we test the gate through a full cycle to see where it binds.
- 3
We write the scope and the price. You get a flat written price before any work begins, listing what will be replaced or welded and what the parts cost. No surprise invoice at the end, per Haven Standard Clause 1.
- 4
We do the repair. Hinges, rollers, posts, rails, latches, and welds are handled on site using the correct hardware for your gate’s weight and frame. We re-check alignment and test the gate by hand and with the operator.
- 5
We document and hand over the record. Before we leave, you get a photo log of every adjustment and a written record of the part numbers installed, plus the 365-Day Done Right Promise covering the work.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Whitney?
Most swing-gate hinge replacements in Whitney run $180 to $320 per hinge set, depending on the hinge type and whether the post needs work. Roller replacement on a sliding gate typically lands between $140 and $280, and a latch or lock replacement runs $120 to $250. Rail repair and smaller custom welds usually fall between $200 and $450, and full post replacement runs $450 to $900 or more, since setting a post plumb and re-hanging the gate is the most involved job in this category.
What moves the price: the gate’s weight and span, whether the metal is steel, aluminum, or wrought iron, and how much damage the failing part caused before you called. Repairs caught early cost less, because worn hinges and rollers that are replaced quickly don’t bend rails or strain the operator. To avoid overpaying, ask for the written scope before work starts so you can see exactly what’s being replaced. Our free estimate includes the inspection, the diagnosis, and a written price agreed before anyone starts, and we’ll review a written estimate from another company at no cost as a second opinion.
Gate Parts & Welding Near Whitney – Our Service Area

We serve Whitney and the surrounding Las Vegas Valley, including Sunrise Manor, Paradise, Winchester, Henderson, Enterprise, Spring Valley, North Las Vegas, and Boulder City. Typical response is same-day for repair calls in the Whitney core and next-day for outlying areas like Sandy Valley. For these neighboring communities, see our Gate Parts & Welding in Sunrise Manor page, and for nearby coverage on the east side, see Gate Parts & Welding in Paradise.
Serving Whitney, NV – Our Local Coverage Area
We serve Whitney and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Gate Parts & Welding in Whitney

Gate parts and welding covers the hardware and metal repair on a gate: hinges, posts, rails, rollers, latches, locks, and any welding the frame needs to stay solid. It’s the repair work that keeps a gate swinging, sliding, and latching correctly before a bigger failure hits the motor. We handle all of it in Whitney, on site, with a written price before we start.
Most hinge, roller, and latch replacements finish in one visit, usually one to three hours. Welding repairs and post replacements take longer, often half a day or more, depending on how much realignment the gate needs afterward. We give you a time estimate with the written scope so you know what to expect.
Small hardware jobs like latch and roller replacement run $120 to $280, hinges run $180 to $320, and welding or post work runs $200 to $900 depending on scope. The final price depends on the gate’s material, weight, and how much damage the failing part caused. Call (844) 797-4861 for an exact quote – estimates are free.
Yes, we service Ghost Controls, DoorKing, Elite, and Mighty Mule, along with LiftMaster, FAAC, BFT, Linear, and Viking. On parts and welding jobs, the brand usually matters less than the gate’s frame and weight, but knowing the operator helps us avoid strain on it. Whether your gate has one of those systems or any other make, we can help.
Yes, a live person answers the phone 24 hours a day, seven days a week, and we offer same-day and emergency service in Whitney for gates that are stuck, dragging, or won’t latch. Call (844) 797-4861 and we’ll confirm the issue and dispatch a technician. For security failures, we’ll tell you on the call what to do until we arrive.
Every repair we complete is covered by the 365-Day Done Right Promise: if the work isn’t right, we make it right at no additional charge within one full year. That covers the hinges, welds, rollers, latches, and posts we install. The photo record we leave with you documents the parts and adjustments, which helps if anything needs a second look.
Clear the area around the gate, unlock it so the technician can cycle it freely, and make sure the driveway is accessible for a vehicle. If you have a written estimate or prior repair record, have it ready so we can compare. If the gate is automated, make sure the breaker or disconnect is accessible so we can safely test the operator. The technician calls ahead and gives you their name and photo before arriving.
Schedule Your Gate Parts & Welding Service in Whitney Today
Worn hinges, a sagging post, or a cracked weld only gets worse, and the repair gets bigger with it. Call (844) 797-4861 and a live person will take your details and dispatch a technician, often the same day in Whitney. You get a free estimate, a written price agreed before work starts, a documented photo record, and the 365-Day Done Right Promise. No obligation, no surprise invoice.
Written by the team at Vance Gate Repair.