Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterAutomatic Gate Repair in Whitney, NV
Automatic gate repair in Whitney, NV covers the motorized side of a driveway gate: the operator, the control board, the safety sensors, the arms and hinges, and the low-voltage wiring that ties them together. If your gate opens halfway and stops, reverses for no reason, or won’t respond to the remote, the problem usually lives in one of those components. Vance Gate Repair Whitney works on nine major automation brands (LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule) so we repair the motor already on your property instead of steering you toward a new one. Call (844) 797-4861 and a live person answers, any hour.
Our technicians have up to 12 years of experience, and every visit follows The Haven Standard: a written price before work starts and a documented photo record before we leave. This page is the automatic-gate branch of our Gate Repair service, and it’s the place to start if the gate still has power but won’t behave.
When You Need Automatic Gate Repair
Most automatic gate failures announce themselves before the gate stops working entirely. These are the symptoms we hear about most in Whitney.
- The gate opens partway and reverses. Usually a misaligned photo-eye (the infrared beam that stops the gate if something crosses the path) or a limit switch set past travel. We photograph the reset position so the next adjustment starts from a known state.
- The remote works only up close. A weak receiver antenna, a dying battery in the transmitter, or interference from a newer device on the same frequency band. Worth ruling out before anyone quotes a control board.
- The gate won’t move but the motor hums. Often a stripped gear, a seized hinge, or a binding track. Replacing the motor when the real fault is a $40 hinge is the most expensive mistake in this trade.
- The gate drifts or slams at the end of travel. Limit switches and deceleration ramps need resetting, and on older DoorKing and Elite operators the slowdown cams wear with age.
- The keypad or intercom stopped calling through. Access-control wiring takes a beating in the desert heat, and a bad splice at the post will take down the whole entry sequence.
- The gate opens on its own. Ghost openings point to a stuck receiver button, a shorted loop, or a control board holding a false signal. This one is worth a same-day look.
Our Automatic Gate Repair Process

We don’t start with a quote. We start with a diagnosis, because the price depends entirely on what’s actually broken. Here’s how a repair visit runs.
- Document the fault before touching anything. We photograph the operator, the control board, the sensor alignment, and the gate’s position at rest. If a previous company worked on it, that record becomes the baseline.
- Test power, signal, and mechanical travel separately. Motor, board, sensors, and hinges each get checked on their own. A gate that “doesn’t work” is often two small faults stacked.
- Read the limit-switch positions and photography them. We record the current settings so any adjustment is traceable. This is the habit our team carried over from commercial access-control work, and it’s why our repair notes read like a wiring diagram instead of a sentence on a napkin.
- Hand you a written price before any work begins. Every part, every hour, in dollars, on paper. Under Haven Standard Clause 1, the price doesn’t change after the fact. If you have a written estimate from another company, we’ll review it at no cost as a free second opinion.
- Complete the repair and reset the safety systems. Photo-eye alignment, force limits, and reverse-on-contact get tested with a physical obstruction before we call it done.
- Leave the photo record and the part numbers with you. Clause 4 (Evidence on every job) means you get a documented log of what was found, what was adjusted, and what was installed. It’s filed in the job record, too.
Every completed repair is covered by the 365-Day Done Right Promise. If something we fixed acts up within that year, we make it right at no additional charge.
Before
AfterAutomatic Gate Repair Pricing in Whitney
Automatic gate repair in Whitney typically runs $150 to $650 depending on the fault, with most single-component repairs landing between $220 and $380. A board or motor replacement pushes the range higher, and we’ll always tell you when repair is the cheaper path. These are honest ranges, not a bait number: the written quote you get on site is the price you pay.
| Repair | Typical range |
|---|---|
| Limit switch reset / travel adjustment | $150 – $250 |
| Photo-eye alignment or sensor replacement | $180 – $320 |
| Remote / receiver diagnosis and repair | $150 – $280 |
| Hinge, roller, or track repair (mechanical) | $200 – $450 |
| Swing-gate arm or operator motor replacement | $450 – $1,200 |
| Control board replacement | $350 – $800 |
| Access-control / keypad wiring repair | $200 – $500 |
What moves the number: the brand (some Ghost Controls and Mighty Mule operators are simpler to service than a DoorKing board), whether the arm bracket is intact, whether the gate itself is binding, and whether the wiring is accessible or buried. We don’t charge a diagnostic fee on jobs we complete. If you already have a written estimate from another company, bring it and we’ll review it free.
FAQs – Automatic Gate Repair

How much does automatic gate repair cost in Whitney?
Most automatic gate repairs in Whitney run $150 to $650, with single-component fixes landing around $220 to $380. Motor and board replacements cost more, and we quote the exact figure in writing before starting. Call (844) 797-4861 for a free estimate.
Can you repair the gate motor I already have, or do I need a new one?
In most cases we repair the existing motor. We service nine major automation brands, including Ghost Controls, DoorKing, Elite, and Mighty Mule, so we’re not limited to one manufacturer’s parts. Replacement is a last resort when the motor itself is failed beyond repair, and we’ll show you why. Call (844) 797-4861 to schedule a diagnostic.
My gate opens by itself. Is that an emergency?
A gate that opens on its own is a safety issue, not just an annoyance, and worth a same-day look. It usually traces to a stuck receiver button, a shorted loop, or a control board holding a false signal. Call (844) 797-4861 and a live person will answer any hour.
Do you offer a warranty on automatic gate repairs?
Yes. Every completed repair is backed by our 365-Day Done Right Promise: if we didn’t fix it right, we make it right within a full year, no argument, no fee. You also get a documented photo record of every adjustment we made. Call (844) 797-4861 for a free estimate.
If your automatic gate is misbehaving, don’t wait for it to fail completely. Call (844) 797-4861 for a free estimate. A live person answers 24/7, we hand you a written price before any work starts, and every visit comes with a photo record you can keep. For the wider range of gate problems we handle, start at our Gate Repair in Whitney page or our home page.
Written by the team at Vance Gate Repair Whitney, serving Whitney.