Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Installation Cost in Whitney?
Gate installation in Whitney typically runs $1,850 to $4,200 for a driveway gate and $650 to $1,900 for a pedestrian gate, hardware and hanging included, with automatic operators adding $900 to $2,600 on top of the gate itself. A basic single-panel tubular steel drive gate with a manual latch usually lands near $2,100, while a dual-swing ornamental gate with two LiftMaster operators and a keypad entry commonly prices between $6,800 and $9,500. Those ranges cover the gate, posts, concrete footings, hardware, hanging, and the written record we leave behind; the exact number depends on span, material, and whether there is existing automation or wiring on the property to work from.
We hand over the price in writing before a single post hole is dug. That is not a sales gesture, it is the first clause of The Haven Standard, the set of rules every Vance Gate Repair job runs on. Homeowners in Whitney call us with a driveway opening, a rough idea of what they want, and a reasonable suspicion that any number quoted over the phone will grow by the time the invoice arrives. So we price it on paper, item by item, and that written figure is what the job costs.
Key Takeaways
- Most Whitney residential driveway gate installs land between $1,850 and $4,200 before automation.
- Automatic operators add $900 to $2,600 for a single gate, more for dual-leaf installs.
- Material drives the price more than any other single factor: steel, aluminum, wrought iron, and wood sit in very different brackets.
- Every install includes a photographed record of the footings, hinge alignment, and operator settings, filed and left with you.
- Written price is delivered before work begins, and the Gate Installation in Whitney service page spells out the scope behind these numbers.
Gate Installation Cost Breakdown (2026)

Here is how a Whitney installation breaks down line by line. These are the figures we actually write on estimates, not national averages pulled from a cost aggregator.
| Line item | Typical range (Whitney, 2026) |
|---|---|
| Driveway gate, single leaf, tubular steel, manual | $1,850 – $2,900 |
| Driveway gate, dual swing, ornamental steel or iron | $3,600 – $6,200 |
| Aluminum ornamental gate, single or dual | $2,800 – $5,400 |
| Wood or composite gate (custom build) | $3,200 – $7,000 |
| Pedestrian / walk-through gate | $650 – $1,900 |
| Posts, concrete footings, and site prep | $450 – $1,400 |
| Hinges, latches, drop rods, and hardware | $180 – $650 |
| Swing gate operator (single arm, installed) | $900 – $1,800 |
| Dual operators (two arms, synchronized) | $1,900 – $2,600 |
| Sliding gate operator with track and wheels | $1,400 – $2,800 |
| Access control: keypad, remote, intercom, or card reader | $220 – $1,100 |
| Safety equipment: photo-eyes, safety edges, loop detector | $280 – $950 |
| Low-voltage wiring run (per 25 ft, if not existing) | $180 – $420 |
| Old gate removal and haul-away | $120 – $380 |
Add it up and you get a realistic picture. A single-leaf steel drive gate with one operator and a keypad, on existing wiring, sits around $3,300 to $4,600 all in. A dual ornamental install with two operators, photo-eyes, and a fresh wiring run lands nearer $7,000 to $9,500.
What pushes a Whitney quote up? Sloped driveways are the big one. A gate hung on a grade needs a different hinge approach and often a higher-clearance operator arm, and that adds labor. Very wide openings, past about 14 feet per leaf, require heavier frames and stronger posts. Existing automation that has to be matched or replaced adds discovery time. And a property where the driveway concrete is already poured limits where the footings can go, which occasionally means cutting and patching.
What pulls it down? A standard-width opening in flat ground, existing low-voltage conduit already run from the house, and a manual gate with no operator at all. We see a lot of newer Whitney builds where the driveway and landscape were finished before the gate went in, and the conduit was pulled during the concrete pour. That saves several hundred dollars on the wiring line every time.
Before
AfterWhat Affects Gate Installation Pricing in Whitney
- Gate material and weight. Tubular steel is the workhorse and the cheapest per foot. Ornamental wrought iron costs more in material and in hanging time because of the weight. Aluminum sits in between and holds up well against the desert sun. Wood and composite are the most expensive to build custom and the most expensive to maintain over time.
- Opening width and leaf count. A single 12-foot leaf is straightforward. Two 10-foot leaves need a synchronized operator system, stronger posts at the hinge points, and a center stop, which is where dual installs climb past the single-gate bracket.
- Soil and grading at the post line. Some Whitney lots sit on ground that needs deeper footings to hold a heavy gate square. A gate hung out of plumb will sag within a season, so we set footings to depth rather than shaving the concrete to save an hour.
- Automation brand and existing equipment. We service nine major gate-automation brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If there is already a working operator on the property, we price the gate to fit it instead of steering you into a replacement you did not ask for.
- Access control and safety devices. A simple remote is cheap. A keypad, intercom, or card reader raises the cost, and photo-eyes and safety edges are not optional on an automatic gate. They are what stops the gate if a child or a pet crosses the path.
- Permits and HOA review. Whitney and the surrounding Clark County area require permits for many gate and operator installs, and most HOAs want a submittal before the gate goes up. We flag those requirements in the written scope so the cost shows up on the estimate rather than as a surprise after the fact. Permit fees themselves are set by the county and vary by scope.
How to Save on Gate Installation

The honest way to save on a gate is to remove work from the job before the estimate is written, not to negotiate after it is signed.
- Keep the opening a standard width. If your driveway can take a 12-foot single leaf instead of two 10-foot leaves, you skip the dual-operator system and the extra posts. That alone can pull several hundred to a couple thousand dollars off the total.
- Run the low-voltage conduit before the concrete. If the driveway is not poured yet, talk to your concrete contractor about pulling a conduit from the house to the gate line while the forms are open. It is a fraction of the cost of trenching afterward.
- Reuse a working operator. If there is a LiftMaster or FAAC unit already on the property that still runs, we can price a new gate to fit it. That is one of the reasons we carry nine brands on our service list rather than one.
- Get a free second opinion on any written estimate. Bring us the paperwork from another company and we will review it at no cost. We have found duplicate line items, missing safety devices, and footings priced twice on estimates that looked reasonable at a glance.
- Ask for the written price, not a phone number. A quoted range over the phone cannot account for your grade, your soil, or your existing wiring. The written figure is the one that holds, and ours is delivered before any work starts.
Estimates are free. Call (844) 797-4861 and we will walk the property, take measurements, and hand you a written scope you can compare against anyone else’s.
How the Installation Actually Runs (Step by Step)
Knowing the sequence helps you read an estimate and spot one that skipped a step.
- Site walk and measurement. We measure the opening, check the grade, look for existing conduit or wiring, and photograph the site. This is where the estimate gets its real numbers.
- Written scope and price. You receive the line-item price in writing before anything is ordered or dug. Under Clause 1 of the Haven Standard, no work starts until you have that document in hand.
- Post setting and footings. Posts are set to depth in concrete and left to cure. A gate hung on an uncured or shallow footing will sag, so this step does not get rushed.
- Gate hanging and alignment. The gate is hung, checked for plumb and swing, and adjusted at the hinges. We photograph the final alignment so any future adjustment has a baseline.
- Operator and safety install. If you are adding automation, the operator is mounted, the limit switches are set to the gate’s actual travel, and photo-eyes and safety edges are installed and tested. The photo-eye is the infrared beam that stops the gate if something crosses the path, and on an automatic gate it is a safety requirement, not an upgrade.
- Documentation and handoff. Before we leave, you get a photo log of the footings, hinge settings, and operator configuration, plus a written record of the part numbers installed. That record lives in the job file and stays with you. It is the same habit our team built on commercial access-control work, and it means no future technician has to guess how your gate was set.
Every completed install is covered by our 365-Day Done Right Promise. If the gate is not right, we make it right within that year at no additional charge.
Repair or Replace? A Fair Question

If your current gate still hangs true and the operator works, a repair is almost always the cheaper path, and we will tell you so. Common repairs like a hinge replacement or a limit switch reset run a fraction of a new install. We do not steer customers toward replacement when repair is the honest answer, and we carry parts and service knowledge across all nine automation brands so we can work on what is already there.
Replacement makes sense when the gate frame is bent beyond straightening, the posts have rotted or pulled out of the ground, or the operator is past the point where parts are available. In those cases the install price above applies, and the old gate removal line covers haul-away.
FAQs – Gate Installation Cost in Whitney
What does a basic driveway gate cost to install in Whitney?
A basic single-leaf tubular steel driveway gate, manual, with posts and footings, runs $1,850 to $2,900 in Whitney. Adding a single swing operator brings the total to roughly $2,800 to $4,600. Call (844) 797-4861 for a written price on your specific opening.
How much does an automatic gate opener add to the installation?
An automatic swing operator adds $900 to $1,800 for a single gate and $1,900 to $2,600 for a synchronized dual-leaf system, installed. Safety devices like photo-eyes and safety edges add $280 to $950 and are required on any automatic gate. Call (844) 797-4861 and we will price the operator and safety package in writing.
Is it cheaper to repair my existing gate or install a new one?
Repair is cheaper in most cases: a hinge replacement, latch fix, or limit switch reset typically runs well under $500, against $1,850 and up for a new install. Replacement wins only when the frame is bent, the posts have failed, or the operator is obsolete. Bring us any written estimate from another company and we will review it free. Call (844) 797-4861.
How long does gate installation take in Whitney?
Most single residential gate installs take one to two days on site, with footings needing time to cure before the gate is hung. Dual-leaf and automated installs usually run two to three days. We schedule around the cure time rather than rushing it. Call (844) 797-4861 to get your install on the calendar.
Do I need a permit to install a gate in Whitney?
Many gate and automatic-operator installs in the Whitney and Clark County area require a permit, and most HOAs require a submittal before work begins. Permit fees are set by the county and vary by scope, so we flag the requirement in your written estimate rather than guessing a figure. Call (844) 797-4861 and we will tell you what your specific job needs.
Why Homeowners in Whitney Call Us

We have completed more than 22,000 gates since 2014, and every one came with a written price before the work started and a documented photo record when the technician left. Our technicians bring up to 12 years of experience to the job. A live person answers the phone 24 hours a day, seven days a week, so you are not sent to voicemail at any hour. The 365-Day Done Right Promise covers every install, and a free second opinion on any competitor’s written estimate is always available.
If you want a gate priced in writing, installed with a photographed record, and backed for a full year, call (844) 797-4861 for a free estimate.
Pricing reflects the Whitney market as of 2026. Vance Gate Repair Whitney offers free estimates – call (844) 797-4861.
Written by the team at Vance Gate Repair Whitney.
What Our Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.