Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Repair in Whitney: What to Know First
We repair Ghost Controls gate openers in Whitney as an independent Ghost Controls service provider, and most single-issue repairs are done in one visit – usually same day when you call before mid-afternoon. Typical repairs run $185 to $520 depending on what failed, and you get the flat price in writing before any work starts, part of The Haven Standard we hold on every visit. This page is for Whitney homeowners who already own a Ghost Controls system and want it fixed right, not sold a replacement. Call (844) 797-4861 and a live person answers, day or night.

How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls builds a solid DIY-friendly line, but the same design choices that make their openers easy to install are the ones that show up as repeat failures down the road. Here’s what we actually find on Whitney gates:
- Limit switch drift on the TDS series (TDS10, TDS12): The TDS models set travel distance with two mechanical stops rather than hard limit switches, and those stops walk out of position over months of use. A gate that stops short or reverses before it should close is usually a stop that slipped by 10 to 15 degrees, not a bad board. We measure the arm travel, reset the stops, and photograph the new positions so it doesn’t creep back.
- Battery and solar charging failures on the AXS and TSS series: These are low-voltage, solar-friendly systems, so the first thing that dies is rarely the motor – it’s the 12V battery or a solar panel that stopped getting sun. A unit that beeps and won’t open in the morning is often just a battery that won’t hold charge. We load-test the battery and panel output separately before recommending either part.
- Arm pin and bracket wear on all swing models: The operator arm brackets take the day-to-day abuse, and on Whitney’s older metal gates the bolts backing out or the bracket wallowing out of round is a common cause of a gate that sags or won’t fully latch. We re-drill worn brackets and re-bolt to solid metal rather than just tightening what’s loose.
- Control board moisture and heat damage: Ghost Controls boards sit exposed to the desert sun and the rare winter rain we get out here. We’ve traced intermittent “phantom opening” faults to water intrusion at the board connections. We reseal the box and replace failed connectors.
- Receiver and remote pairing dropouts: When the remote stops working, the culprit is usually the receiver board or an antenna that’s been bent or corroded, not the remote. We test the receiver directly before asking you to buy a new remote.
One thing worth saying plainly: a lot of “failed” Ghost Controls openers we get called out to in Whitney just need a limit stop reset, a fresh battery, or a bracket re-bolt. Our technicians have up to 12 years of experience and we’d rather fix the $40 part than quote a $1,200 motor. That’s the whole reason we put the price in writing before touching a tool.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Repair Process

- 1
Phone diagnosis. A live person takes the call, notes your model (look for the sticker on the control box), and what the gate is doing. We tell you the likely range right then.
- 2
On-site inspection. We test the whole system – battery, solar input if present, board, receiver, arm, and brackets – and show you the readings.
- 3
Written scope and price. Before any work, you get the flat price in writing, with an OEM Ghost Controls part or a quality aftermarket equivalent named and priced side by side.
- 4
The repair. We replace or reset the failed component, re-seal the control box, and re-bolt brackets to solid metal.
- 5
The test cycle. We run the gate open and closed a full cycle, check the safety reverse, and confirm the limits hold.
- 6
Documentation and cleanup. You get a photo log of what was found, what was set, and what was installed, left with you and filed in the job record. Under Clause 4 (Evidence on every job), that’s included at no charge.
See the difference
Before
After
Before
After
Before
After
Before
AfterWhat Ghost Controls Gate Repair Costs in Whitney
| Repair | Typical Range |
|---|---|
| Limit stop reset / travel adjustment | $135 – $195 |
| Battery or solar panel replacement | $150 – $260 |
| Receiver or remote pairing repair | $120 – $200 |
| Arm bracket re-bolt / re-drill | $185 – $340 |
| Control board replacement | $280 – $520 |
What moves the price: whether the bracket bolts into solid metal or needs re-drilling, whether the part is a genuine Ghost Controls OEM piece or a quality aftermarket equivalent, and whether it’s a single component or a couple of stacked faults. Battery-only calls land at the low end, board-and-bracket jobs at the high end. We quote the flat price in writing and it doesn’t change once you approve it – no surprises at the end. Call (844) 797-4861 for a free estimate on your job.
Why Whitney Homeowners Call Vance Gate Repair Whitney for Ghost Controls Work

We’ve repaired and installed 22,000+ gates since 2014, and every job has been run the same way: written price before work starts, a documented photo record when the technician leaves, and the 365-Day Done Right Promise – one full year for us to make any repair right at no additional charge. Our technicians are background-checked and uniformed, and you get their name and photo before they arrive. We also service eight other major brands, including LiftMaster, Mighty Mule, and DoorKing, so a Whitney homeowner with a mixed setup isn’t steered toward a whole-system swap. We fix the Ghost Controls system you have – we don’t push replacement when a repair will do. And you can bring us a written estimate from another Whitney company for a free second opinion.

FAQs
Yes. Every completed Ghost Controls repair we do is covered by our 365-Day Done Right Promise – one full year for us to make it right at no extra charge. We stand behind the work, not just the part.
Both, and we price them side by side so you can choose. On most repairs a quality aftermarket equivalent performs fine and costs less; for boards and receivers we usually lean OEM Ghost Controls for fit and reliability. You see both prices in writing before we order anything.
Usually, yes – most single-issue Ghost Controls repairs get done in one visit if you call before mid-afternoon, and a live person answers day or night. We’ll tell you on the phone whether it’s a same-day job or one that needs a part ordered. Call (844) 797-4861 for an exact quote – estimates are free.
Repair is the right call for most Ghost Controls failures – limit drift, batteries, receivers, and brackets are all fixable on the existing system. We don’t recommend replacement unless the board, motor, and arm are all failing together, and even then we’ll show you the numbers before you decide.
Yes. Beyond Ghost Controls, we service LiftMaster, FAAC, BFT, Linear, Viking, DoorKing, Elite, and Mighty Mule, so we can work on whatever motor is already on your property rather than steering you toward one brand. If you’ve got a mixed setup, we fix what’s there.
Ready to get your Ghost Controls gate back in service? Call (844) 797-4861 for a free estimate – a live person answers 24/7, and we’ll give you a written price before any work starts.
Written by the team at Vance Gate Repair Whitney, serving Whitney and nearby areas.