Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Repair Before & After in Whitney, NV
Claims are easy. Seeing the work is not. Below is a record of gate repair jobs in Whitney, NV: what we found when we arrived, what we adjusted or replaced, and what the gate does now. Every job follows the Haven Standard – written price first, photo record at the end – so each transformation is documented, not just described.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Recent Transformations
Sagging Double Swing Gate – Hinge and Post Repair
Before
AfterThe problem: A double drive gate in a Whitney neighborhood had dropped on its hinges until the outer panel dragged across the concrete and the latch no longer caught.
What we did: We reset both hinge plates, shimmed the post-side brackets, and replaced the worn bottom hinge. The latch and drop rod were realigned to engage without force.
The result: The gate now swings level and clears the driveway through the full arc. The homeowner got a photo log showing the new hinge positions and part numbers before we left.
Gate Opener Stopped Mid-Travel – Limit Switch Reset
Before
AfterThe problem: A LiftMaster swing operator kept stopping about two-thirds of the way open, and the homeowner had been holding the remote to nurse it through.
What we did: The limit switch had drifted roughly 12 degrees past travel. We reset it to the correct position, re-taught the run limits, and photographed the new setting.
The result: The gate opens and closes fully in one press. We logged the limit position and photographed it so any future technician starts from a known baseline.
Photo-Eye Beam Misalignment – Safety Edge Fault
Before
AfterThe problem: An automatic gate would reverse at random and sometimes stop open entirely. The culprit was a photo-eye knocked about two inches out of alignment, so the beam was catching the ground instead of its reflector.
What we did: We squared the mounting brackets, re-aimed both eyes, and tested the reversal path across the full swing. Safety beams are a genuine hazard to get wrong, so this is not a fix we’d ever suggest a homeowner attempt alone.
The result: The gate now completes its cycle reliably and reverses correctly when the beam is broken. A photographed record of the corrected bracket positions went with the homeowner.
Weathered Wrought-Iron Gate – Welding and Refinish

The problem: A wrought-iron pedestrian gate had a cracked weld at the base of two pickets and rust spreading under the paint along the bottom rail.
What we did: We re-welded the failed joints, ground them smooth, treated the rust, and refinished the affected sections to match the rest of the gate.
The result: The gate is solid again, the pickets no longer flex, and the repair reads as original ironwork rather than a patch.
Sliding Gate Off Its Track – Roller and Track Service

The problem: A sliding driveway gate had begun to bind and hop the track, and the opener was straining against the resistance.
What we did: We replaced the worn rollers, cleared debris and concrete lips from the track, and readjusted the gate’s tracking guides so it rode centered.
The result: The gate glides through its full travel with the opener working well within its load. The homeowner can now open it by hand without fighting it if power ever drops.
Cantilever Gate Opener – Control Panel and Access Repair

The problem: A cantilever gate with a DoorKing access system stopped responding to keypad codes, and the homeowner was stuck using the manual release every time.
What we did: We traced the fault through the control panel, corrected the wiring, and re-programmed the entry codes. The panel covers the automation on the property, whatever the brand.
The result: Entry codes work again and the manual release is back in the emergency role it’s meant for. The wiring diagram and photo record went into the job file.
Want Results Like These?

If your gate is sagging, sticking, reversing without warning, or simply not answering the remote, call us at (844) 797-4861. A live person answers 24 hours a day. You’ll get a written price before any work begins and a photo record of what we found and fixed when we’re done. Every repair is covered by the 365-Day Done Right Promise. Estimates are free.
Written by the team at Vance Gate Repair Whitney.
See the difference
Before
After
Before
After
Before
After