Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHinge & Post Repair in Whitney, NV
Hinge and post repair fixes the two things that hold a gate square: the hinges that carry the leaf and the posts that anchor everything else. When a gate sags, drags, or won’t latch cleanly, the cause is almost always one of those two, and the fix is a targeted repair rather than a new gate. We handle this work across Whitney and the surrounding east-side neighborhoods, with the flat price written and handed to you before a tool comes off the truck. Call (844) 797-4861 and a live person picks up, any hour.
Most companies quote hinge work by feel. We photograph the hinge plate, measure the post plumb, and record the reading before and after, so the next person to touch your gate knows exactly what was found and what was set. That habit comes from commercial access-control work, where a gate that fails open or fails to close is a documented liability, and it carried over intact to residential driveway gates. If you’re looking at a broader problem than hinges and posts alone, start on our Gate Repair in Whitney page and we’ll point you to the right scope.
Our technicians have up to 12 years of experience, and every visit under The Haven Standard leaves you a photo log of what was adjusted, what was replaced, and the part numbers that went in. If the repair doesn’t hold, the 365-Day Done Right Promise covers it for a full year at no additional charge.
When You Need Hinge & Post Repair
Sagging is the obvious symptom. It’s the ones that show up quietly that catch homeowners off guard, especially in a desert climate where posts move seasonally with the soil.
- The gate drags on the ground at the latch side. A dropped leaf almost always means hinge wear or a post that has leaned a degree or two. In Whitney’s summer heat, wooden posts dry and shrink while steel hinges stay put, so the gap opens up and the leaf drops.
- The gate won’t stay open or swings on its own. That’s usually a hinge binding rather than a gate that’s out of balance. A binding hinge also loads the opener arm, which is why a Ghost Controls or Mighty Mule motor can start straining without an obvious reason.
- You can see daylight between the post and the concrete. A post that has pulled loose at the base is a structural problem, not a cosmetic one. Wind load on a wide gate multiplied by a loose footing is how gates fall.
- The post leans after a monsoon storm or a sprinkler line break. Saturated soil around a post footing softens fast, and a gate that was plumb in June can be a half-inch off by August. We check plumb on every hinge call for exactly this reason.
- Rust streaks run down from the hinge plates. Weld-on hinges on steel frames rust from the inside out at the weld seam. Catching it early means re-welding a plate rather than replacing the frame section.
- The gate latches only if you lift it. That lift is the tell. It means the leaf has dropped relative to the strike post, and the fix is a hinge adjustment or replacement rather than shimming the latch.
If your opener is also acting up, our gate motor repair in Whitney page covers the electrical side, since a binding hinge and a failing motor often show the same symptom from the driver’s seat.
Our Hinge & Post Repair Process

Every hinge and post job follows the same sequence, so you know what’s happening and in what order. Nothing starts until the written scope and price are in your hand.
- Assess and document the failure. We photograph each hinge, measure the post for plumb, check the footing for movement, and test the gate swing by hand. You get those photos whether or not you hire us for anything beyond the assessment.
- Write the scope and price. The flat price covers the specific repair we found, in writing, before any work starts. If the assessment turns up a bent frame or a failed footing that changes the job, we tell you and re-quote rather than surprising you at the end.
- Stabilize the post first. Hinges can’t hold if the post is moving. We reset or re-anchor the post, confirm plumb, and let the footing set before hanging weight back on it.
- Repair or replace the hinges. Worn hinges get replaced with matched hardware; weld-on plates get re-welded and dressed; adjustable hinges get set to the correct gap and swing. We photograph the new position and record the part numbers.
- Re-hang and adjust the leaf. We set the gate level, check the latch alignment, and confirm the swing clears the ground across its full arc. If there’s an opener, we re-test the limit switches so the arm isn’t fighting a hinge that now moves freely.
- Leave the record. Before we go, you get the photo log and a written record of everything adjusted and installed. It’s filed in the job record too, so a future technician isn’t guessing at what’s underneath.
One safety note worth stating plainly: a wide gate leaf can weigh several hundred pounds, and a post that lets go while someone is working under it causes serious injury. Post and hinge work on heavy or automated gates is not a homeowner job. We use bracing and supports on every call, and we’d rather turn down a repair than watch a gate come down on someone.
Before
AfterHinge & Post Repair Pricing in Whitney
Hinge and post repair in Whitney typically runs $180 to $650, and most single-hinge replacements land under $300. Post resetting and footing work push toward the top of that range because the labor and cure time are higher. What you pay depends on the repair we actually find, and the flat price is written for you before we start.
| Repair | Typical range |
|---|---|
| Single hinge replacement (standard swing gate) | $180 – $280 |
| Full hinge set replacement on a double gate | $320 – $520 |
| Weld-on hinge plate repair or re-weld | $220 – $400 |
| Post reset or re-anchor (existing footing) | $280 – $550 |
| New post and footing (post replacement) | $450 – $650 |
| Adjustable hinge upgrade (matched set) | $240 – $420 |
What moves the number: gate material and weight, whether the post is steel or wood, whether the footing needs to be broken out and re-poured, and whether the gate is automated. A gate with a DoorKing or Elite opener takes extra re-testing time after the hinge work, because the limits have to be verified against the new swing. That’s built into the quote, not added later.
If another company has already handed you a written estimate, bring it in. Our free second opinion reviews the paperwork at no cost, and we’ll tell you if the scope matches what we’d write. Estimates are free, and the number you get is the number you pay.
Can you repair a gate post without replacing it?

Usually, yes. A post that’s leaning or has pulled slightly at the footing can often be re-anchored and reset in place, which costs less than a full replacement and keeps the original post and gate hardware matched. If the post itself is rotted, cracked, or bent below grade, replacement is the honest answer, and we’ll show you the photos that explain why.
Hinge and post repair in Whitney often gets skipped in favor of a new gate, and that’s usually unnecessary. A reset post and a fresh set of hinges fix the same symptom for a fraction of the cost. Call (844) 797-4861 and we’ll walk you through what we’d expect to find.
How do I know if my gate needs new hinges or just an adjustment?
If the gate moves freely by hand but sits low or won’t latch, the hinges usually just need adjustment. If the leaf binds, grinds, or squeals through part of its swing, the hinge has worn or the pin has bent and replacement is the better call. The difference matters because adjusting a worn hinge only buys a few months.
We check this in person in a few minutes and tell you which repair is warranted rather than which is more profitable. Reach us at (844) 797-4861 for a free estimate.
Can you repair hinges and posts on an automated gate?

Yes, and it’s one of the more common jobs we run. Automated gates carry extra load on their hinges because the opener pushes the leaf rather than a person swinging it, so worn hinges show up faster. After any hinge or post work, we re-test the opener’s limit switches and safety sensors so the gate stops and reverses where it should.
We service all nine major automation brands, including Ghost Controls, DoorKing, and Elite, so you don’t get steered toward a new motor just because the repair touches an automated gate. Call (844) 797-4861 and we’ll quote the hinge work and the opener check together.
How long does a hinge and post repair take?
Most single-hinge jobs are done in under two hours. A post reset adds cure time because the footing has to set before the gate goes back on it, so plan on a same-day repair or, for a full post replacement, a return visit once the concrete is ready. We tell you the schedule up front instead of leaving you guessing.
Scheduling a repair is straightforward: call (844) 797-4861, describe what the gate is doing, and we’ll tell you what the assessment is likely to find and when we can be there. A live person answers at any hour.
If your gate is dragging, leaning, or won’t latch cleanly, the hinge and post repair is usually the fix rather than a replacement. Call (844) 797-4861 for a free estimate. You’ll get the flat price in writing before any work starts and a documented photo record when we leave. And if you’d like to understand the wider repair picture first, our home page lays out how we work.
Written by the team at Vance Gate Repair Whitney, serving Whitney.