Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Welding & Fabrication: The Whitney Owner’s Guide
We install Ghost Controls-compatible welding and fabrication repairs for driveway gates in Whitney, and most welded repairs land between $220 and $650 installed, depending on whether the mount post needs re-pinning, whether the arm bracket is cracked, or whether a new hinge plate has to be cut and welded. Same-day service is available when a failed weld has left your gate stuck open or off its track. That price is written and handed to you before any tool comes out of the truck, per The Haven Standard Clause 1.

Most owners find this problem the hard way. The gate motor runs, the arm strokes, and the gate hangs at an angle or drags on the ground. Often the cause is not the opener at all – it’s a weld on the mount post, the arm bracket, or the gate frame that has cracked where fatigue and Nevada heat worked it loose. By the time you notice, the weld has usually been failing for weeks and the swing geometry has already drifted, which is why diagnosing the weld and resetting the opener always go together in our shop.
Which Ghost Controls Models This Applies To
Ghost Controls runs several lines that land on Whitney gates – the AXS, TSS1, and DTP1 series are common, along with the older TSS and ARD models still on plenty of driveways here. The good news is that the welding and fabrication side is mostly universal. Every one of those openers bolts to a mount post and drives an arm or actuator against a gate frame. If either of those structures has failed, the fix is fab work, not a new opener – and that is true whether the box on the gate is a Ghost Controls unit, a LiftMaster, a Mighty Mule, or a DoorKing.
To identify exactly what you’re working with, look at the label inside the opener housing or the plate under the arm bracket. Note the model number and the serial. Then measure two things: the bolt spacing on the mount post plate, and the swing clearance from the gate hinge. Those two numbers decide whether a replacement bracket can be the OEM part or has to be cut and welded to fit your specific post. If the label is sun-bleached and unreadable, a photo of the arm and the post plate is usually enough for us to identify it.
On the OEM-versus-aftermarket question, we recommend sticking with Ghost Controls parts for the electrical side – the control board, the limit switches, the arm internals – because aftermarket boards have burned us and homeowners more than once in the Nevada heat. For the structural welding and fabrication, there is no meaningful “Ghost Controls” part to buy. That work is cut, fit, welded, and painted on site to match your post and gate. So the decision there is not OEM vs aftermarket; it’s whether the fabricator measures and photographs before cutting. Ours do.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Welding & Fabrication Is Failing

Here’s what we actually find when a Whitney homeowner calls about a Ghost Controls gate that’s misbehaving. If any of these line up, the problem is likely structural, not electrical:
- Gate sags or hangs at an angle when the opener is disengaged. That’s a hinge or post weld that’s cracked. If the gate drops when you pull the manual release, the weld was carrying load it was never meant to carry.
- Opener arm binds or “jumps” mid-swing. The arm bracket weld has failed or the mount post has shifted by a degree or two. Binding shows up first at the halfway point, then progresses.
- Visible crack or rust line at a weld joint. On Whitney gates, our summer heat and winter wind load work weld heat-affected zones hard. A hairline crack with rust bleed means the weld is already open.
- Mount post wobbles when you push the gate. The concrete footing or the post base has loosened. Ghost Controls arms are relatively low-force, so a wobble here usually points to a bad base weld or a foot that has shifted in the caliche soil.
- Opener strokes fully but the gate stops short. The weld that ties the arm to the gate frame has flexed, changing the effective arm length. The opener thinks it has finished its travel because the limit switch fires; the gate says otherwise.
Any of these on their own is worth a look. Two or more is a structural issue that will burn out the opener if it isn’t fixed first. We see that pattern often on Whitney gates, and it’s the most expensive path – the homeowner replaces the opener, the new opener cracks in ninety days, and the weld finally gets addressed.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Whitney address, most Ghost Controls welding and fabrication repairs run between $220 and $650 installed. A cracked arm bracket re-weld with re-pinning is at the low end of that range. A full mount-post base re-weld with footing repair pushes toward the top. If the gate frame itself needs a new hinge plate cut, fitted, and welded, expect the range to extend above the top figure and for us to write a specific line for it in the written quote before work starts.
What drives the price is geometry, not brand. The bigger the misalignment we have to correct, the more fabrication. What you get for the price:

- On-site diagnosis with limit-switch readings and a photo of the failed weld before we touch anything
- The fabrication itself, welded and painted to match your gate
- Reset of the Ghost Controls arm to the new geometry, with the new limit positions photographed
- Cycle test and a written record of the part numbers and settings installed
- 365-Day Done Right Promise: if the repair is not right, we make it right at no additional charge
No surprise invoice at the end. The price you read is the price you pay, and the flat figure is handed over in writing before the first weld.
DIY or Call Us?

Some of this is safe to check yourself. You can safely disengage the opener with the manual release, swing the gate by hand, and note whether it drops, binds, or wobbles. You can photograph the mount post and the arm bracket. You can read the model label. That’s it. That’s the boundary.
The welding itself is not a driveway job. Arc welding and metal cutting throw molten spatter, produce UV that will damage your eyes even through sunglasses, and require a fire watch for thirty to sixty minutes afterward – Nevada dry grass and wood fencing catch fire fast. Getting a weld right on a gate that carries a motor’s load takes more than a machine from a box store. A bad weld can fail under load and drop the gate on a person. We’re not going to walk you through that; we’d rather do it once, do it right, and hand you the photo record when we’re done.
If you’ve got a Ghost Controls gate that’s sagging, cracking, or dragging, call us at (844) 797-4861. A live person answers 24/7, and we’ll get an exact written price in front of you before any work begins.
FAQs
A properly welded and painted repair on a Ghost Controls mount post or arm bracket typically lasts ten to fifteen years in Whitney conditions, sometimes longer if the gate is well-balanced and the opener arm is set to the correct force. The failure we see most is a weld that was never painted after the crack was treated, which lets our UV and dust get into the seam. We paint every weld we leave behind.
Yes – nearly always. On a Ghost Controls installation, the mount post, arm bracket, and gate frame can be re-welded, re-pinned, or reinforced rather than replaced. We only recommend a new bracket or post when the original metal has thinned below a safe cross-section, which is rare outside of gates that have been sitting in standing water. Ask about a repair first; you’ll hear an honest answer. Call (844) 797-4861 for a free estimate.
A cracked arm bracket re-weld and reset is usually a two to three-hour visit. A mount post base re-weld with footing work runs a full afternoon, and, in rare cases, we come back the next day for paint and cycle testing. We don’t leave a gate in manual mode overnight if it’s the only barrier on the property – we’ll tell you what’s realistic when we quote it.
For the electrical side, we source Ghost Controls parts through authorized distribution – no aftermarket control boards on our jobs. For the structural fabrication, we don’t source anything from a shelf. The bracket and reinforcement are cut, fit, and welded on site to match your specific post and gate. That’s why we measure and photograph before we cut, and why the price is written before the first weld. Call (844) 797-4861 to get an exact quote – estimates are free.
Written by the team at Vance Gate Repair Whitney, serving Whitney and nearby areas.
Vance Gate Repair Whitney is an independent service provider and is not affiliated with Ghost Controls. We service Ghost Controls alongside LiftMaster, FAAC, BFT, Linear, Viking, DoorKing, Elite, and Mighty Mule – one company that can work on whatever motor is already on your property. Call (844) 797-4861 for a free estimate and a written price before any work starts.