Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Replacement: The Whitney Owner’s Guide
We replace Ghost Controls gate motors in Whitney with a written installed price usually between $620 and $1,150, depending on the model series, gate weight, and whether the arm bracket and control board are still sound. Motor swaps are commonly scheduled same day, and someone answers the phone at (844) 797-4861 around the clock to set it up.

Owners usually find out the hard way. The gate stops reversing when it meets an obstacle, or it opens partway and stalls, or the arm runs but the gate barely moves. Sometimes there’s a clicking sound from the control box and nothing else. In Whitney, we see a lot of this after a stretch of 105-degree afternoons, when the motor housing has been baking in direct sun and the internal components start to drift or seize. A failing motor rarely dies cleanly. It gives you weeks of odd behavior first, and that window is when a replacement is cheapest and easiest.
Vance Gate Repair is an independent service provider. We’re not affiliated with Ghost Controls, though we do work on their equipment regularly.
Key Takeaways
- Installed Ghost Controls motor replacement in Whitney typically runs $620 to $1,150.
- Most failures are diagnosed from the control box, the arm, or the limit settings, not from guesswork.
- We provide a written price before any work begins, under The Haven Standard.
- We handle the low-voltage wiring and safety photo-eye alignment on every replacement.
- Ghost Controls is one of nine automation brands we service, alongside LiftMaster, Mighty Mule, and DoorKing.
Which Ghost Controls Models This Applies To
Ghost Controls builds primarily single and dual swing-gate operators, and the series matters when you’re matching a replacement motor or arm. The most common residential lines are the single-arm AXS and TSS series and the dual-arm DTP and DTPS kits. The gate operator itself carries a label, usually on the inside of the control box housing, that lists the model and the supply voltage. If the label is faded, measure the arm: the tube length and the stroke distance tell us which replacement arm fits without drilling new mounting holes.
That measurement is the compatibility gotcha most owners miss. A replacement arm that’s close but not exact will mount, but it won’t reach full open or it will over-travel and trip the limit switch. Getting the stroke right the first time saves you a second visit.
On the OEM versus aftermarket question, Ghost Controls’ own replacement arms and control boards are the safest match for series-specific control logic, but we also carry quality aftermarket equivalents that meet the same stroke and voltage specs at a lower price. We’ll tell you which is which and let you choose. We don’t stock parts on a truck. Every replacement is ordered to the job, which is one reason the written quote includes the exact part number before you approve it.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Gate Motor Replacement Is Failing

These are the symptoms we hear most often from Whitney homeowners, and what’s usually behind each one:
- The gate won’t reverse when it hits something. The photo-eye (the infrared beam that stops the gate if a person or car crosses the path) has drifted out of alignment or failed. This is a safety-critical fault and shouldn’t be ignored.
- The gate opens partway and stalls. The motor is losing torque, often because heat has degraded the windings or the gear assembly inside the arm is worn.
- The arm runs but the gate barely moves. The motor turns but the drive linkage inside the arm is stripped, or the arm has separated from its bracket.
- Clicking from the control box with no movement. The control board’s relay or the start capacitor has failed. A capacitor is a cheap fix; a board is a bigger decision.
- The gate drifts open on its own or won’t hold position. The limit switch has slipped or the control logic has lost its travel calibration.
What ties these together in Whitney is heat and dust. Gates here face a long, hot summer and fine desert grit that works into moving parts. A motor that’s five or six years old and showing two of these symptoms is usually past repair. One symptom alone often isn’t.
See the difference
Before
After
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what a Ghost Controls gate motor replacement typically costs for a Whitney homeowner, installed:
| Item | Typical Installed Range |
|---|---|
| Single-arm motor and arm replacement | $620 – $850 |
| Dual-arm motor replacement | $900 – $1,150 |
| Control board replacement only | $260 – $420 |
| Photo-eye alignment or replacement | $120 – $240 |
| Arm bracket or mounting repair | $90 – $200 |
What drives the range: whether it’s a single or dual gate, the model series, whether the mounting bracket is intact or needs rebuilding, and whether the low-voltage wiring needs attention. The quote separates parts from labor so you can see what you’re paying for. Nothing gets ordered or installed until the written price is in your hands and you’ve approved it.
Our work is covered by the 365-Day Done Right Promise. If something isn’t right within a year, we make it right at no additional charge.
DIY or Call Us?

Some things you can safely check yourself. Look at the control box label to confirm the model. Clear any debris or vegetation blocking the photo-eye path. Check that the arm is firmly attached to its bracket. Press the manual release to see whether the gate swings freely by hand. If it does, the problem is likely mechanical or in the motor; if it doesn’t, the gate itself may be binding.
What you shouldn’t do yourself: open the motor housing or attempt to rewire the low-voltage connections. Those circuits run through the control board and the safety devices, and a miswire can leave the gate operating without working reversal protection, which is a real injury risk. We’ve also seen homeowners buy a replacement arm that’s close to the right stroke and end up with a gate that over-travels every cycle. For a Whitney homeowner with a 30-minute phone call available at (844) 797-4861, a trained technician and a written price are the faster path.
FAQs
How long does a Ghost Controls gate motor last?
A Ghost Controls motor typically lasts six to ten years under normal use, but Whitney’s summer heat is hard on the electronics inside the housing: we commonly see the control board and capacitors wear out on the earlier end of that range when a gate sits in full afternoon sun. Keeping the housing clean and shaded where possible helps.
Can my Ghost Controls motor be repaired instead of replaced?
Sometimes, yes. A failed start capacitor or a drifted limit switch is a repair, not a replacement, and we’ll tell you plainly if that’s the case. A motor that’s lost torque, a stripped drive linkage inside the arm, or a burnt-out control board usually points to replacement. We give you the honest read and the written price for whichever option applies. Call (844) 797-4861 to get it looked at.
How long does the swap take?
A single-arm Ghost Controls motor replacement usually takes about two to three hours on site, including the wiring check and photo-eye alignment. Dual-arm gates and bracket rebuilds can run four to five hours. We schedule same-day in most cases and give you a time window when we book.
How do you source the replacement part?
We order the replacement to your exact model and arm spec based on the label and physical measurements, then photograph the part number on the unit before we install it so you have a record. We don’t claim to carry parts on a truck. If you’ve got a written estimate from another company, bring it over and we’ll give you a free second opinion on it.
If your Ghost Controls gate is misbehaving in Whitney, call us at (844) 797-4861 for a free estimate. We’ll schedule the visit, hand you a written price before anything starts, and leave with a photo record of what was found, what was set, and what went in.
Written by the team at Vance Gate Repair Whitney, serving Whitney and nearby areas.