A Vance company - serving Whitney, NV

Ghost Controls Gate Motor & Opener in Whitney, NV

Wrought ironWrought iron
Wood & steel frameWood & steel frame
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Ghost Controls Gate Motor & Opener in Whitney: What to Know First

Vance Gate Repair Whitney provides independent Ghost Controls gate motor and opener service in Whitney, and most repair visits are completed on the first trip with the correct part on hand. We’re not affiliated with or authorized by Ghost Controls; we’re an independent Ghost Controls service provider that works on the equipment already mounted on your property. The price is written and handed to you before any tool comes out, and you get a photo record of every adjustment when we leave.

Technician performing maintenance on an automatic gate motor and opener in Whitney, NV

Call (844) 797-4861

This page is for Whitney homeowners who already own a Ghost Controls system and want a straight answer on what’s wrong, what it costs, and whether it’s a repair or a replacement. If you’d rather talk it through, call (844) 797-4861 and a live person picks up, any hour.

How Ghost Controls Products Fail – and How We Fix Them

Ghost Controls is a DIY-friendly brand, and that’s exactly why we see the same handful of failures repeat across Whitney driveways. The motors are sound. What fails is usually the install geometry, the battery, or a limit setting that drifted. Here’s what we actually find:

  • Limit switches set past travel (TSS1 and TSS1XP single-swing units). The most common call we get. The gate slams the post because the open or close limit is set a few degrees beyond the physical stop. We reset the limits, photograph the new position, and test the obstruction reverse before we pack up. Left alone, that slamming eventually cracks the arm bracket.
  • Battery sag on solar and battery-backup setups (AXO and TSS series). Ghost Controls runs on DC battery with optional solar, and in Whitney’s summer heat a sealed lead-acid pack loses capacity faster than owners expect. The gate slows, then stalls halfway. We load-test the battery under the motor’s actual draw rather than trusting a resting voltage reading, which is where most DIY diagnoses go wrong.
  • Control board moisture and corrosion. The control box on a Ghost Controls kit sits low and exposed. Irrigation overspray and monsoon-season humidity get into the enclosure and corrode the terminal block. We find it as intermittent open commands that work one day and not the next. Fix is usually a terminal cleanup and reseal, not a new board.
  • Arm bracket and hinge wear on slide and swing conversions. The push-pull arm takes the load, and a worn bracket makes a healthy motor look weak. We check bracket play before condemning the operator, because a $40 part solves what looks like a $600 problem.
  • Photo-eye (the infrared beam that stops the gate if something crosses the path) misalignment. Kids, dogs, and yard crews knock the eyes out of line, and the gate refuses to close. We realign, verify the beam at the actual mounting height, and photograph the corrected alignment so the next person doesn’t chase it again.
Explore

Styles & brands we work with

  • Wrought iron
  • Wood & steel frame
  • Farm & ranch
  • Sliding driveway gates
  • LiftMaster operators

Our Ghost Controls Gate Motor & Opener Process

Technician performing professional maintenance on a residential sliding gate opener motor.
Our Ghost Controls Gate Motor & Opener Process
  1. 1
    Phone diagnosis. A live person answers 24/7 and asks what the gate does, not what you think is broken. We note the model line and the symptom before we dispatch.
  2. 2
    On-site diagnostic. We test the battery under load, read the limit positions, check the control board and terminals, and inspect the arm and brackets. No guessing, no parts cannon.
  3. 3
    Written price, then your decision. Under Haven Standard Clause 1, you get the flat price in writing before any work starts. If it’s a repair, we repair. If the motor is genuinely done, we say so and price the replacement separately.
  4. 4
    Parts call: OEM or quality aftermarket. Ghost Controls OEM parts keep the warranty intact where it applies. Good aftermarket equivalents cost less and often outlast the original on a battery. We show you both and explain the trade-off.
  5. 5
    Repair and full test cycle. We run open, close, obstruction reverse, and battery-backup cutover before we call it finished.
  6. 6
    Documentation and guarantee. You get a photo log of every adjustment and the part number installed, filed in the job record. The work is covered by the 365-Day Done Right Promise.
BeforeBefore
AfterAfter

What Ghost Controls Gate Motor & Opener Costs in Whitney

Most Ghost Controls repair visits in Whitney land between $150 and $340, but the exact number depends on what failed. Here’s how it breaks down:

Job Typical Range
Limit switch reset and adjustment $130 – $200
Battery replacement (sealed lead-acid) $150 – $280
Control board / terminal repair $180 – $340
Arm bracket or hinge replacement $160 – $300
Full Ghost Controls motor replacement $550 – $1,100

What moves the number: whether the unit is a slide or swing operator, solar versus straight battery, and whether the arm hardware is intact. The written price is handed over before work starts, so there’s no invoice surprise at the end. Call (844) 797-4861 for a free estimate.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Why Whitney Homeowners Call Vance Gate Repair Whitney for Ghost Controls Work

professional gate repair service
Why Whitney Homeowners Call Vance Gate Repair Whitney for Ghost Controls Work

We’ve repaired and installed 22,000+ gates since 2014, and every single one got a written price before the job and a documented record when the technician left. That’s the whole point of The Haven Standard – and the 365-Day Done Right Promise means if the repair isn’t right, we make it right at no charge for a full year. Our technicians have up to 12 years of experience and are background-checked, with name and photo sent before arrival. Ghost Controls is one of nine brands we service, alongside LiftMaster, Mighty Mule, and DoorKing, so we never steer you toward a replacement because it’s the only motor we know. If you’re in Whitney and want a straight answer, call (844) 797-4861. We also offer a free second opinion on any written estimate you’ve gotten elsewhere.

Get the price in writing before anything starts.A real person answers, day or night.
Call now

FAQs

Contact Vance Gate Repair Whitney

Technician performing metal gate repair with an angle grinder
Contact Vance Gate Repair Whitney

Whether your Ghost Controls gate is slamming the post, stalling halfway, or dead in the driveway, call (844) 797-4861 for a free estimate. A live person answers 24/7, the written price comes before any work starts, and the photo record and 365-Day Done Right Promise come after. We’re your Ghost Controls gate motor and opener resource in Whitney.

Written by the team at Vance Gate Repair Whitney, serving Whitney and nearby areas.

Need Gate Repair help nationwide? Licensed & insured · 1-hour response · free estimates
Call (844) 797-4861
Local Service Coverage

Request a Free Estimate in Whitney

Tell us what you need - Vance Gate Repair Whitney responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Us
Call Now - 24/7 Dispatch